+- Wanderlodge Gurus - The Member Funded Wanderlodge Forum (http://www.wanderlodgegurus.com)
+-- Forum: Yahoo Groups Archive (/forumdisplay.php?fid=61)
+--- Forum: WanderlodgeForum (/forumdisplay.php?fid=63)
+--- Thread: 3208 T'Stats - What's The Drill (/showthread.php?tid=660)
3208 T'Stats - What's The Drill - freewill2008 - 05-21-2005 05:03
Changing some hoses and the thermostats on this 225T this morning.
First, am I looking in the right place: the stat housing is just below
the air conditioning compressor, correct?
The housing is not like the book, of course! Has a rad hose fitting
piggy-backed on it, apparently. Two of the housing bolts look like
studs that run out through the hose fitting. The nuts on those studs
(?) loosen and then the studs spin without turning out.
I'm probably missing something here. Anyone?
Bob Griesel '84 FC31 WLII WA
3208 T'Stats - What's The Drill - pattypape - 05-21-2005 05:16
I struggled with this same problem.
The expert Mike H set me straight.
All that stuff is bolted to an assessory plate on our
300 hp turbo. We could easily reach the bolt/nuts from
inside the doghouse. There is also some confusion on
a one or two thermostat system. Our 88 has only one thermostat.
Just get dirty and crawl into the doghouse with a bright light.
Bill 88 FC Michigan Likes being in the doghouse
--- In WanderlodgeForum@yahoogroups.com, "freewill2008"
> Changing some hoses and the thermostats on this 225T this
morning.
>
> First, am I looking in the right place: the stat housing is just
below
> the air conditioning compressor, correct?
>
> The housing is not like the book, of course! Has a rad hose
fitting
> piggy-backed on it, apparently. Two of the housing bolts look
like
> studs that run out through the hose fitting. The nuts on those
studs
> (?) loosen and then the studs spin without turning out.
>
> I'm probably missing something here. Anyone?
>
> Bob Griesel '84 FC31 WLII WA
3208 T'Stats - What's The Drill - randydupree - 05-21-2005 10:32
nuts and bolts on the ones i've done..randydupree93wb
----- Original Message -----
From: freewill2008
To: WanderlodgeForum@yahoogroups.com
Sent: Saturday, May 21, 2005 1:03 PM
Subject: [WanderlodgeForum] 3208 T'Stats - What's The Drill
Changing some hoses and the thermostats on this 225T this morning.
First, am I looking in the right place: the stat housing is just below
the air conditioning compressor, correct?
The housing is not like the book, of course! Has a rad hose fitting
piggy-backed on it, apparently. Two of the housing bolts look like
studs that run out through the hose fitting. The nuts on those studs
(?) loosen and then the studs spin without turning out.
I'm probably missing something here. Anyone?
Bob Griesel '84 FC31 WLII WA
------------------------------------------------------------------------------
Yahoo! Groups Links
a.. To visit your group on the web, go to:
http://groups.yahoo.com/group/WanderlodgeForum/
b.. To unsubscribe from this group, send an email to:
WanderlodgeForum-unsubscribe@yahoogroups.com
c.. Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.
[Non-text portions of this message have been removed]
3208 T'Stats - What's The Drill - freewill2008 - 05-22-2005 06:47
Yeah - *nuts* working on the engine and *bolts* holding it
together.
When I saw Bill's reply earlier I remembered reading awhile back about the bolt heads behind the stat housing.
Anyway, it was a good day's preventive maintenance. New stats, upper
rad hoses, oil cooler hoses, power steering return hoses. Found much
better routing for the PS hoses - no more loops and pinches. Also
fabricated a little vent for the PS fluid resevoir. Worked outdoors
and buttoned up the front just as the rain started.
100 mile test drive tomorrow to drop the rig off for the Telma
install.
Bob Griesel '84 FC31 WLII in showery western WA
--- In WanderlodgeForum@yahoogroups.com, randydupree
wrote:
> nuts and bolts on the ones i've done..randydupree93wb
> ----- Original Message -----
> From: freewill2008
> To: WanderlodgeForum@yahoogroups.com
> Sent: Saturday, May 21, 2005 1:03 PM
> Subject: [WanderlodgeForum] 3208 T'Stats - What's The Drill
>
>
> Changing some hoses and the thermostats on this 225T this
morning.
>
> First, am I looking in the right place: the stat housing is just
below
> the air conditioning compressor, correct?
>
> The housing is not like the book, of course! Has a rad hose
fitting
> piggy-backed on it, apparently. Two of the housing bolts look
like
> studs that run out through the hose fitting. The nuts on those
studs
> (?) loosen and then the studs spin without turning out.
>
> I'm probably missing something here. Anyone?
>
> Bob Griesel '84 FC31 WLII WA
>
>
>