Wanderlodge Gurus - The Member Funded Wanderlodge Forum
Added a gauge cluster... - Printable Version

+- Wanderlodge Gurus - The Member Funded Wanderlodge Forum (http://www.wanderlodgegurus.com)
+-- Forum: Yahoo Groups Archive (/forumdisplay.php?fid=61)
+--- Forum: WanderlodgeForum (/forumdisplay.php?fid=63)
+--- Thread: Added a gauge cluster... (/showthread.php?tid=7286)



Added a gauge cluster... - Ryan Wright - 10-23-2008 15:04

...& my oil pressure is just fine, folks. Mechanical unit verified
60lbs at startup. The sending unit for the front gauge is shot. I'll
get a new one ordered in the morning.

In the meantime, I added a cluster of three gauges in the back of the
coach tonight:

http://www.ryanwright.com/tmp/eng-gauge1.jpg
http://www.ryanwright.com/tmp/eng-gauge2.jpg

They look real purty all lit up. I've got a mechanical oil pressure
gauge on the right, volts in the center and coolant temp on the left -
haven't hooked the coolant temp lead up yet, though. Still trying to
figure out how to go about that one. Anyway, they're tied into the
rear lighting so they only come on with the engine door open. This was
a pretty easy project once I found that oil pressure sending unit.
Cost me all of forty bucks and will come in real handy when doing any
sort of engine troubleshooting.

Huge thanks for all of the advice on that sending unit.

-Ryan
'86 PT-40 8V92


Added a gauge cluster... - Scott Forman - 10-24-2008 10:22

How did you hook up the oil press gauge? This is on my list to do as
well.

Scott Forman
86 PT38
Memphis

--- In WanderlodgeForum@yahoogroups.com, "Ryan Wright"
wrote:
>
> ...& my oil pressure is just fine, folks. Mechanical unit verified
> 60lbs at startup. The sending unit for the front gauge is shot. I'll
> get a new one ordered in the morning.
>
> In the meantime, I added a cluster of three gauges in the back of
the
> coach tonight:
>
> http://www.ryanwright.com/tmp/eng-gauge1.jpg
> http://www.ryanwright.com/tmp/eng-gauge2.jpg
>
> They look real purty all lit up. I've got a mechanical oil pressure
> gauge on the right, volts in the center and coolant temp on the
left -
> haven't hooked the coolant temp lead up yet, though. Still trying to
> figure out how to go about that one. Anyway, they're tied into the
> rear lighting so they only come on with the engine door open. This
was
> a pretty easy project once I found that oil pressure sending unit.
> Cost me all of forty bucks and will come in real handy when doing
any
> sort of engine troubleshooting.
>
> Huge thanks for all of the advice on that sending unit.
>
> -Ryan
> '86 PT-40 8V92
>


Added a gauge cluster... - Kurt Horvath - 10-24-2008 10:37

I see exhaust blankets!

Firwin priced out my system at 191.00 for turbo & manifold, 350.00
for the pipes to base of muffler, 150.00 for muffler or stack, not to
bad.

Scott how about some more details on new gauges, I think this is a
great idea.

Then again there are few upgrades I don't like. :}

Kurt Horvath
95 PT 42
10AC

--- In WanderlodgeForum@yahoogroups.com, "Scott Forman"
<scottforman75@...> wrote:
>
> How did you hook up the oil press gauge? This is on my list to do
as
> well.
>
> Scott Forman
> 86 PT38
> Memphis
>
> --- In WanderlodgeForum@yahoogroups.com, "Ryan Wright"
> wrote:
> >
> > ...& my oil pressure is just fine, folks. Mechanical unit verified
> > 60lbs at startup. The sending unit for the front gauge is shot.
I'll
> > get a new one ordered in the morning.
> >
> > In the meantime, I added a cluster of three gauges in the back of
> the
> > coach tonight:
> >
> > http://www.ryanwright.com/tmp/eng-gauge1.jpg
> > http://www.ryanwright.com/tmp/eng-gauge2.jpg
> >
> > They look real purty all lit up. I've got a mechanical oil
pressure
> > gauge on the right, volts in the center and coolant temp on the
> left -
> > haven't hooked the coolant temp lead up yet, though. Still trying
to
> > figure out how to go about that one. Anyway, they're tied into the
> > rear lighting so they only come on with the engine door open.
This
> was
> > a pretty easy project once I found that oil pressure sending unit.
> > Cost me all of forty bucks and will come in real handy when doing
> any
> > sort of engine troubleshooting.
> >
> > Huge thanks for all of the advice on that sending unit.
> >
> > -Ryan
> > '86 PT-40 8V92
> >
>


Added a gauge cluster... - Donald Watson - 10-24-2008 12:35

Ryan,

Nice job on the engine compartment gauge cluster, especially the switched
back lighting. A mechanical oil pressure gauge makes sense. I didn't find
mention of 'parallel gauge' issues in previous posts leading up to the one
I'm responding to. If you weren't already aware of it, electrical gauges
are resistive devices. When you stack one on top of the other, such as two
identical water temp gauges, the parallel resistance of the gauges is now
half what the sending unit was designed for. The result can be an erroneous
gauge reading sometimes twice what it should be.

To take this into account, you either have to have two separate sending
units or a sending unit specified as handling two gauges. That special
sending unit can only be used with two gauges and not one. If an additional
water temp sending unit is installed, it is important to have it located
where it will give an honest reading of engine coolant temperature; just any
threaded plug in the coolant system might not be appropriate. Another issue
is the location of a coolant temp too high in the system. If the coolant
level falls below the sensor, it will no longer be reading coolant temp.

Newer engines incorporate warning indicators and some auto shutdown
procedures. Older engines may include after-market alarms for high coolant
temperature or low oil pressure, but the later is tricky on two cycle
Detroits that might exhibit as little as 8 lbs at idle, but still be
healthy. Alarm sensors (switches) are a topic for another discussion.

Gauges, got to have them. Even better, training the eye to scan them
regularly while driving.

Regards,

Donn
76 FC33
South Kingstown, RI



From: WanderlodgeForum@yahoogroups.com
[mailto:WanderlodgeForum@yahoogroups.com] On Behalf Of Ryan Wright
Sent: Thursday, October 23, 2008 11:04 PM
To: wanderlodgeforum
Subject: [WanderlodgeForum] Added a gauge cluster...

...& my oil pressure is just fine, folks. Mechanical unit verified
60lbs at startup. The sending unit for the front gauge is shot. I'll
get a new one ordered in the morning.

In the meantime, I added a cluster of three gauges in the back of the
coach tonight:

http://www.ryanwright.com/tmp/eng-gauge1.jpg
http://www.ryanwright.com/tmp/eng-gauge2.jpg

They look real purty all lit up. I've got a mechanical oil pressure
gauge on the right, volts in the center and coolant temp on the left -
haven't hooked the coolant temp lead up yet, though. Still trying to
figure out how to go about that one. Anyway, they're tied into the
rear lighting so they only come on with the engine door open. This was
a pretty easy project once I found that oil pressure sending unit.
Cost me all of forty bucks and will come in real handy when doing any
sort of engine troubleshooting.

Huge thanks for all of the advice on that sending unit.

-Ryan
'86 PT-40 8V92



Added a gauge cluster... - Ryan Wright - 10-27-2008 11:47

On Fri, Oct 24, 2008 at 3:22 PM, Scott Forman <scottforman75@...> wrote:
> How did you hook up the oil press gauge? This is on my list to do as
> well.

Scott,

See the picture of my existing oil pressure sending units here:
http://www.ryanwright.com/tmp/sensor.jpg

There are two extra ports there. I took out the plug in the left port
(next to the little sensor) and screwed the adapter that came with the
gauge cluster right onto there. A thin tube (also came with the
gauges) then carries oil up to the gauge, and pressure is sensed that
way. I zip-tied (lightly so as not to crush the tubing) the tube to
various places along the way. I fabricated the bracket out of angle
iron, it attaches to existing bolts behind that ignition box, so no
drilling or modification of coach parts was required. I try to
structure any modifications so as to be invisibly reversible wherever
possible.

I may have to drill into my cooling system somewhere to mount the
sensor for the temperature gauge. I'm not excited about doing this...
I'll probably fabricate a small metal box containing the sensor, then
place it between two sections of existing flexible coolant line, so it
can also be un-done.

-Ryan
'86 PT-40 8V92