Fan Shaft Seal Leaking

[Curt Sprenger]

Has anyone replaced the engine fan shaft seal? Do you know where to get
the seal? Mine is leaking. I want to take care of that before remounting
the fan.

--
Curt Sprenger
1987 PT38 8V92 "MacAttack Racing"
Anaheim Hills, Calif.

[ernieekberg@...>]

Curt- Ralph, Bim and myself did a seal replacement on my coach. If you have the
radiator removed have at it. We did it with the radiator in place. If I have to
do that again- the coach is up for sale~
Ernie Ekberg
83PT40
Livingston,Montana
----- Original Message -----
From: Curt Sprenger
To: WanderlodgeForum@yahoogroups.com ; wanderlodge@yahoogroups.com
Sent: Wednesday, February 21, 2007 3:50 PM
Subject: [WanderlodgeForum] Fan Shaft Seal Leaking



Has anyone replaced the engine fan shaft seal? Do you know where to get
the seal? Mine is leaking. I want to take care of that before remounting
the fan.

--
Curt Sprenger
1987 PT38 8V92 "MacAttack Racing"
Anaheim Hills, Calif.





[Non-text portions of this message have been removed]

[Curt Sprenger]

Ernie,
Does the 6V and 8V have the same fan set up? If so, I'd like to see you
guys tackling that project with the radiator in place. Must have been a
two box wine job, per person. How many hours went into that job?

Curt Sprenger
1987 PT38 8V92 "MacAttack Racing"
Anaheim Hills, Calif.



ernieekberg@... wrote:

> Curt- Ralph, Bim and myself did a seal replacement on my coach. If you
> have the radiator removed have at it. We did it with the radiator in
> place. If I have to do that again- the coach is up for sale~
> Ernie Ekberg
> 83PT40
> Livingston,Montana
> ----- Original Message -----
> From: Curt Sprenger
> To: WanderlodgeForum@yahoogroups.com
> ;
> wanderlodge@yahoogroups.com
> Sent: Wednesday, February 21, 2007 3:50 PM
> Subject: [WanderlodgeForum] Fan Shaft Seal Leaking
>
> Has anyone replaced the engine fan shaft seal? Do you know where to get
> the seal? Mine is leaking. I want to take care of that before remounting
> the fan.
>
> --
> Curt Sprenger
> 1987 PT38 8V92 "MacAttack Racing"
> Anaheim Hills, Calif.
>
> [Non-text portions of this message have been removed]
>
>

[Terry Neal]

Curt, as I recall on my PT, I took that seal down to the local
bearing/seal shop (US Bearings) and they matched it up in a few
minutes. You can also try a shop that builds hydraulic hoses. They
might carry the hydraulic fans & parts. Spencer Power here in MT
carries that stuff.

Terry Neal
Bozeman, MT
82PT40 6V92TA
74FC34 6V53T



Curt Sprenger wrote:

>
> Has anyone replaced the engine fan shaft seal? Do you know where to get
> the seal? Mine is leaking. I want to take care of that before remounting
> the fan.
>
> --
> Curt Sprenger
> 1987 PT38 8V92 "MacAttack Racing"
> Anaheim Hills, Calif.
>
>



[Non-text portions of this message have been removed]

[ernieekberg@...>]

Curt- I believe it took 2 days. You can get the fan motor off, and leave the fan
resting on a support bracket. You get real messy, and the weather was perfect.
The only other job that was worse, was R/R an airbag on Ralphs coach. 3 days on
that one.
Ernie Ekberg
83PT40
Livingston,Montana
----- Original Message -----
From: Curt Sprenger
To: WanderlodgeForum@yahoogroups.com
Sent: Wednesday, February 21, 2007 4:42 PM
Subject: Re: [WanderlodgeForum] Fan Shaft Seal Leaking


Ernie,
Does the 6V and 8V have the same fan set up? If so, I'd like to see you
guys tackling that project with the radiator in place. Must have been a
two box wine job, per person. How many hours went into that job?

Curt Sprenger
1987 PT38 8V92 "MacAttack Racing"
Anaheim Hills, Calif.

ernieekberg@... wrote:

> Curt- Ralph, Bim and myself did a seal replacement on my coach. If you
> have the radiator removed have at it. We did it with the radiator in
> place. If I have to do that again- the coach is up for sale~
> Ernie Ekberg
> 83PT40
> Livingston,Montana
> ----- Original Message -----
> From: Curt Sprenger
> To: WanderlodgeForum@yahoogroups.com
> ;
> wanderlodge@yahoogroups.com
> Sent: Wednesday, February 21, 2007 3:50 PM
> Subject: [WanderlodgeForum] Fan Shaft Seal Leaking
>
> Has anyone replaced the engine fan shaft seal? Do you know where to get
> the seal? Mine is leaking. I want to take care of that before remounting
> the fan.
>
> --
> Curt Sprenger
> 1987 PT38 8V92 "MacAttack Racing"
> Anaheim Hills, Calif.
>
> [Non-text portions of this message have been removed]
>
>





[Non-text portions of this message have been removed]

[Curt Sprenger]

Thanks Terry. There is a bearing and seal shop about 5 miles from me.

Curt Sprenger
1987 PT38 8V92 "MacAttack Racing"
Anaheim Hills, Calif.



Terry Neal wrote:

> Curt, as I recall on my PT, I took that seal down to the local
> bearing/seal shop (US Bearings) and they matched it up in a few
> minutes. You can also try a shop that builds hydraulic hoses. They
> might carry the hydraulic fans & parts. Spencer Power here in MT
> carries that stuff.
>
> Terry Neal
> Bozeman, MT
> 82PT40 6V92TA
> 74FC34 6V53T
>
> Curt Sprenger wrote:
>
> >
> > Has anyone replaced the engine fan shaft seal? Do you know where to get
> > the seal? Mine is leaking. I want to take care of that before remounting
> > the fan.
> >
> > --
> > Curt Sprenger
> > 1987 PT38 8V92 "MacAttack Racing"
> > Anaheim Hills, Calif.
> >
> >
>
> [Non-text portions of this message have been removed]
>
>

[Gregory OConnor]

Curt, Off Maple in Corona is King bearing now called Applied
Industrial Technologies
361 S Maple St
Corona, CA 92880

(951) 371-2550


Or In Fontan "O rings and things" across from the speedway.
Gregory O'Connor
94ptRomolandCa


--- In WanderlodgeForum@yahoogroups.com, Curt Sprenger
wrote:
>
>
> Has anyone replaced the engine fan shaft seal? Do you know where to
get
> the seal? Mine is leaking. I want to take care of that before
remounting
> the fan.
>
> --
> Curt Sprenger
> 1987 PT38 8V92 "MacAttack Racing"
> Anaheim Hills, Calif.
>

[Curt Sprenger]

Thanks Greg.
I was trying to come up with the name. Where the H%$L did Applied
Industrial Technologies get substituted for King Bearing? Just doesn't
seem like a good name change if they want to keep bearing & seal
customers coming in. Probable a buy out with no consideration. Thanks again.

Curt Sprenger
1987 PT38 8V92 "MacAttack Racing"
Anaheim Hills, Calif.



Gregory OConnor wrote:

> Curt, Off Maple in Corona is King bearing now called Applied
> Industrial Technologies
> 361 S Maple St
> Corona, CA 92880
>
> (951) 371-2550
>
>
> Or In Fontan "O rings and things" across from the speedway.
> Gregory O'Connor
> 94ptRomolandCa
>
> --- In WanderlodgeForum@yahoogroups.com
> , Curt Sprenger
> wrote:
> >
> >
> > Has anyone replaced the engine fan shaft seal? Do you know where to
> get
> > the seal? Mine is leaking. I want to take care of that before
> remounting
> > the fan.
> >
> > --
> > Curt Sprenger
> > 1987 PT38 8V92 "MacAttack Racing"
> > Anaheim Hills, Calif.
> >
>
>