Overheating 3208 in a 90SP36
|
08-09-2006, 06:12
Post: #3
|
|||
|
|||
Overheating 3208 in a 90SP36
Hello Chuck,
My 3208 is in the front rather than the back but your experiences were much like mine while climbing mountain passes in Colorado. Not sure you can expect any lower temperatures than what you're getting in hot summer weather. I found on my coach that it helps some to gear down as your speed drops off to keep RPM's up so the fan cools better and the engine load is reduced. Regards, Eric 84FC35SBWL2 --- In WanderlodgeForum@yahoogroups.com, "williamcharrison" wrote: > > Just came back from a long trip and noticed that at every extended > grade climb the temp gauge would start climbing toward 220. > It never reached 220 but the level increase alarms me. I have > cleaned the radiator and put new belts on all around. The oil temp > also climbs to about 230 (though I don't know what the danger level > is). The thermostat was replaced before my first trip this year > and I had no similar problems, but then the temperature was in the 70's > and on the last trip it was in the 90's. > > Chuck Harrison > Akron, Ohio > 90SP36 > |
|||
« Next Oldest | Next Newest »
|
Messages In This Thread |
Overheating 3208 in a 90SP36 - williamcharrison - 08-09-2006, 05:33
Overheating 3208 in a 90SP36 - Mike Hohnstein - 08-09-2006, 05:52
Overheating 3208 in a 90SP36 - Eric Johnson - 08-09-2006 06:12
Overheating 3208 in a 90SP36 - Eric Johnson - 08-09-2006, 08:40
Overheating 3208 in a 90SP36 - Tom Seitz - 08-09-2006, 09:42
Overheating 3208 in a 90SP36 - Rovers - 08-09-2006, 10:13
Overheating 3208 in a 90SP36 - davidkerryedwards - 08-09-2006, 10:21
Overheating 3208 in a 90SP36 - erniecarpet@... - 08-09-2006, 10:29
Overheating 3208 in a 90SP36 - Mike Hohnstein - 08-09-2006, 14:07
Overheating 3208 in a 90SP36 - Pete Masterson - 08-09-2006, 14:08
Overheating 3208 in a 90SP36 - Mike Hohnstein - 08-09-2006, 14:15
Overheating 3208 in a 90SP36 - Mike Hohnstein - 08-09-2006, 14:22
Overheating 3208 in a 90SP36 - Mike Hohnstein - 08-09-2006, 15:22
Overheating 3208 in a 90SP36 - Eric Johnson - 08-09-2006, 15:31
Overheating 3208 in a 90SP36 - Mike Hohnstein - 08-09-2006, 15:50
Overheating 3208 in a 90SP36 - Gregory OConnor - 08-09-2006, 17:14
Overheating 3208 in a 90SP36 - Tom Warner - 08-10-2006, 00:37
Overheating 3208 in a 90SP36 - Eric Johnson - 08-10-2006, 01:06
Overheating 3208 in a 90SP36 - Tom Warner - 08-10-2006, 01:48
Overheating 3208 in a 90SP36 - pattypape - 08-10-2006, 02:14
Overheating 3208 in a 90SP36 - dthollis1961 - 08-10-2006, 02:47
Overheating 3208 in a 90SP36 - Scott - 08-10-2006, 04:49
Overheating 3208 in a 90SP36 - davidkerryedwards - 08-10-2006, 05:03
Overheating 3208 in a 90SP36 - erniecarpet@... - 08-10-2006, 06:12
Overheating 3208 in a 90SP36 - erniecarpet@... - 08-10-2006, 07:48
Overheating 3208 in a 90SP36 - erniecarpet@... - 08-10-2006, 09:42
Overheating 3208 in a 90SP36 - erniecarpet@... - 08-10-2006, 09:46
Overheating 3208 in a 90SP36 - Scott - 08-10-2006, 11:00
Overheating 3208 in a 90SP36 - Gardner Yeaw - 08-10-2006, 11:10
Overheating 3208 in a 90SP36 - pattypape - 08-10-2006, 12:16
Overheating 3208 in a 90SP36 - Eric Johnson - 08-10-2006, 12:50
Overheating 3208 in a 90SP36 - Eric Johnson - 08-10-2006, 13:01
Overheating 3208 in a 90SP36 - davidkerryedwards - 08-10-2006, 13:21
Overheating 3208 in a 90SP36 - Eric Johnson - 08-10-2006, 14:47
Overheating 3208 in a 90SP36 - Scott - 08-10-2006, 16:18
Overheating 3208 in a 90SP36 - Howard O. Truitt - 08-10-2006, 23:17
Overheating 3208 in a 90SP36 - Scott - 08-11-2006, 03:49
Overheating 3208 in a 90SP36 - Jeff Miller - 08-11-2006, 13:50
Overheating 3208 in a 90SP36 - Jeff Miller - 08-11-2006, 14:05
Overheating 3208 in a 90SP36 - Gardner Yeaw - 08-11-2006, 14:26
Overheating 3208 in a 90SP36 - Eric Johnson - 08-11-2006, 14:50
Overheating 3208 in a 90SP36 - Jim - 08-11-2006, 16:27
Overheating 3208 in a 90SP36 - Scott - 08-12-2006, 02:39
Overheating 3208 in a 90SP36 - Gregory OConnor - 08-12-2006, 03:38
Overheating 3208 in a 90SP36 - Stephen Birtles - 08-13-2006, 08:39
|
User(s) browsing this thread: 2 Guest(s)