Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Jack Stands
02-09-2007, 22:43
Post: #10
Jack Stands
Thanks Paul,

Your advice is a great help and makes sense. After all,
the drive axle does support the entire weight of the rear
of the coach when the air is dumped from the Tag. How
do you jack up the drive axle? Where do you place the
jack - on the differential pumpkin? What kind of jack
or jacks do you use?

Thanks,
David Brady
'02 LXi, Smokey
NC

PRWillms@... wrote:
> Hi Dave, DO NOT support your coach with you tag. It is only rated at 10,000
lbs only!! Use the side frame that is part of the solid frame. Or what I do is
use my leveling jacks to lighten the weight on the axle then jack up the axel to
place the stands. Using 2 each 20,000# stands should be fine. Remember you are
not supporting the whole weight of the coach. Rull of thumb, Use the stand rated
at or higher then what the drive axel is rated for and only use 2 at a time.
> Good luck,
>
>
> Paul Williams 88XXV 8V92
> In South Lake Tahoe
> -----Original Message-----
> From: dmb993@...
> To: wanderlodge@yahoogroups.com; WanderlodgeForum@yahoogroups.com
> Sent: Fri, 9 Feb 2007 9:47 PM
> Subject: [WanderlodgeForum] Jack stands
>
> Folks,
>
> I need to do some work under my bus. I bought a pair of 20
> ton OTC jack stands and plan to use my HWH jacks to jack
> the rear of the bus and the OTC jack stands to support it once
> lifted. I read the file "working safely under your bus" and note
> that the jack stands need to be positioned under the frame rails
> or under the axles. Is it reasonable to place the jack stands under
> the tag axle. My LXi has a tag axle that's supported by a torque
> arm per side. Where the torque arm bolts to the axle there's a
> nice flat surface area for the jack stand. This means that the tag
> axle will need to be lifted so that the bump stop is pressing
> against the frame rail, then the stand can be place under the tag
> axle with the forces working thru the bump stop. In your opinion,
> is this safe? The back end of my bus weighs 33,000 lbs, and I'm
> working on a level 6" plus thick concrete floor, with tire chalks.
>
> Thanks,
> David Brady
> '02 LXi, Smokey
> NC
>
> ________________________________________________________________________
> Check out the new AOL. Most comprehensive set of free safety and security
tools, free access to millions of high-quality videos from across the web, free
AOL Mail and more.
>
>
> [Non-text portions of this message have been removed]
>
>
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
Quote this message in a reply
Post Reply 


Messages In This Thread
Jack Stands - birdshill123 - 05-27-2006, 05:41
Jack Stands - Gregory OConnor - 05-27-2006, 05:51
Jack Stands - davidkerryedwards - 05-27-2006, 05:58
Jack Stands - davidkerryedwards - 05-27-2006, 06:00
Jack Stands - Jeff Miller - 05-27-2006, 09:57
Jack Stands - Mike Hohnstein - 05-27-2006, 10:40
Jack Stands - Gregory OConnor - 05-28-2006, 04:16
Jack Stands - David Brady - 02-09-2007, 17:47
Jack Stands - PRWillms@... - 02-09-2007, 18:01
Jack Stands - David Brady - 02-09-2007 22:43
Jack Stands - PRWillms@... - 02-09-2007, 23:38
Jack Stands - David Brady - 02-10-2007, 00:09
Jack Stands - Gregory OConnor - 02-10-2007, 00:57
Jack Stands - Gardner Yeaw - 02-10-2007, 10:17
Jack Stands - M Thomas Eastham - 02-11-2007, 15:43
Jack Stands - Gregory OConnor - 02-11-2007, 17:05



User(s) browsing this thread: 1 Guest(s)