Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Jack Stands
02-10-2007, 10:17
Post: #14
Jack Stands
Gregory,
I agree that the jack stands should take the load. If they are
not in contact with the frame and the jack fails, the coach will
drop onto the stands. The inertia could far exceed the jack stands
rateing. Also, the sudden change in attitude could cause the coach
to rock to one side or the other. I wouldn't want to be under it
when that happened. Also, by putting the weight on the jack stands
you are assured of the stability before going under. And like you
said, something extra like that steel rim just in case.

Another note, jack stand pairs can be rated at 20k when actually
each is only 10k. Be sure of what yours really are.

Gardner
78FC33

--- In WanderlodgeForum@yahoogroups.com, "Gregory OConnor"
wrote:
>
> David, I always slide an old steel wheel under somthing low and
solid
> as a landing point. I also drop the HWH but do not put weight on
> them. ( I allow Jack stands to take the load.
> GregoryO'Connor
>
> --- In WanderlodgeForum@yahoogroups.com, David Brady
> wrote:
> >
> > Folks,
> >
> > I need to do some work under my bus. I bought a pair of 20
> > ton OTC jack stands and plan to use my HWH jacks to jack
> > the rear of the bus and the OTC jack stands to support it once
> > lifted. I read the file "working safely under your bus" and note
> > that the jack stands need to be positioned under the frame rails
> > or under the axles. Is it reasonable to place the jack stands
under
> > the tag axle. My LXi has a tag axle that's supported by a torque
> > arm per side. Where the torque arm bolts to the axle there's a
> > nice flat surface area for the jack stand. This means that the
tag
> > axle will need to be lifted so that the bump stop is pressing
> > against the frame rail, then the stand can be place under the tag
> > axle with the forces working thru the bump stop. In your opinion,
> > is this safe? The back end of my bus weighs 33,000 lbs, and I'm
> > working on a level 6" plus thick concrete floor, with tire
chalks.
> >
> > Thanks,
> > David Brady
> > '02 LXi, Smokey
> > NC
> >
>
Quote this message in a reply
Post Reply 


Messages In This Thread
Jack Stands - birdshill123 - 05-27-2006, 05:41
Jack Stands - Gregory OConnor - 05-27-2006, 05:51
Jack Stands - davidkerryedwards - 05-27-2006, 05:58
Jack Stands - davidkerryedwards - 05-27-2006, 06:00
Jack Stands - Jeff Miller - 05-27-2006, 09:57
Jack Stands - Mike Hohnstein - 05-27-2006, 10:40
Jack Stands - Gregory OConnor - 05-28-2006, 04:16
Jack Stands - David Brady - 02-09-2007, 17:47
Jack Stands - PRWillms@... - 02-09-2007, 18:01
Jack Stands - David Brady - 02-09-2007, 22:43
Jack Stands - PRWillms@... - 02-09-2007, 23:38
Jack Stands - David Brady - 02-10-2007, 00:09
Jack Stands - Gregory OConnor - 02-10-2007, 00:57
Jack Stands - Gardner Yeaw - 02-10-2007 10:17
Jack Stands - M Thomas Eastham - 02-11-2007, 15:43
Jack Stands - Gregory OConnor - 02-11-2007, 17:05



User(s) browsing this thread: 1 Guest(s)