EMS 50C

[Rob Robinson]

Sounds possible.

On 25/03/07, Gregory OConnor wrote:
>
> Rob , then there must be a transfer switch for the inverter after the
> shore - genset transfer switch and closer to the Wanderlodge power
> fuse pannel?????
>
> GregoryO'Connor
> 94ptRomolandCa
>
> --- In WanderlodgeForum@yahoogroups.com,
> "Rob Robinson"
> wrote:
> >
> > My mistype Dan. I installed mine after not before the transfer
> switch. I
> > guess my inverter does not go through the transfer switch. When on
> inverter
> > I do not get any reading on the EMS display. I do get readings
> while the gen
> > or shore power are selected.
> >
> > On 25/03/07, ac7880 wrote:
> > >
> > > Rob,
> > > If you wire the EMS before the transfer switch, you have to choose
> > > one input for the EMS (shore or generator or invertor). There are
> > > multiple inputs into the transfer switch(es), but should only be
> one
> > > output to the circuit breaker panel
> > >
> > > So for instance if you choose to use the shore power input into
> the
> > > EMS, generator and invertor are still available, but the coach is
> > > not surge protected from the gen or invertor output.
> > >
> > > If you install after the transfer switch, shore, gen, invertor
> power
> > > introduction into the coach are all checked. I installed on the
> > > shore cable just prior to the transfer switch due to easier
> install
> > > location with my setup, and also to ensure the two transfer
> switches
> > > are also protected from a shore power surge. I distrust the shore
> > > power the most.
> > >
> > > Dan
> > > 94 BB BMC 37' NM
> > >
> > > --- In
WanderlodgeForum@yahoogroups.com
> > 40yahoogroups.com>,
> > > "Rob Robinson"
> > > wrote:
> > > >
> > > > Bill as I understand it, if you have the EMS wired before the
> > > Transfer
> > > > Switch and either the shore power or the generator malfunction
> the
> > > > functional one will still be available. In other words, if the
> > > genny started
> > > > putting out funky power this would only cause the genny to be
> > > obstructed.
> > > > Correct shore power would still get through. Is this correct???
> > > >
> > > > On 25/03/07, Wilhelmus Schreurs wrote:
> > > > >
> > > > > Mike:
> > > > > It also has a feature for frequency, so if the frequency or
> > > voltage is out
> > > > > of whack on the generator the contactor would not pull in.
> > > > > Mike, everyone has there own reasons for doing things, and
> IMHO,
> > > I would
> > > > > want the EMS to protect as much as it is capable of. Is this
> EMS
> > > the perfect
> > > > > solution, no, but it is the best there is available that I
> have
> > > been able to
> > > > > find.
> > > > >
> > > > > Bill 84 FC 35 SB "$quanderlodge"
> > > > > Terrace, B.C. Canada
> > > > >
> > > > > ----- Original Message ----
> > > > > From: mbulriss <mbulriss@ <mbulriss%40yahoo.com>>
> > > > > To:
WanderlodgeForum@yahoogroups.com
> > 40yahoogroups.com> > > > 40yahoogroups.com>
> > > > > Sent: Sunday, March 25, 2007 1:56:44 PM
> > > > > Subject: [WanderlodgeForum] Re: EMS 50C
> > > > >
> > > > > Bill,
> > > > >
> > > > > That's why mine is being installed (when I get to it) only on
> the
> > > > >
> > > > > shore power, so I can still have gen set power.
> > > > >
> > > > > Mike Bulriss
> > > > >
> > > > > 1991 WB40 "Texas Minivan"
> > > > >
> > > > > San Antonio, TX
> > > > >
> > > > > --- In WanderlodgeForum@ yahoogroups. com, Wilhelmus Schreurs
> > > > >
> > > > >
> > >
> > >
> > >
> >
> >
> >
> > --
> > Rob, Sue & Merlin Robinson
> > 94 WLWB
> >
> >
> > [Non-text portions of this message have been removed]
> >
>
>
>



--
Rob, Sue & Merlin Robinson
94 WLWB


[Non-text portions of this message have been removed]