Side Camera

[jim riordan]

Don,

When I installed my voyager I removed the old crt and got a piece of Lexan for
the local plastic place, cut to fit the area covers the hole and then I velcroed
the monitor to the Lexan. works great. I also left room to mount Tom Tom go on
that piece of lexan. all close to see and read.

Jim Riordan
88 WBWL XXV
Stuart, Fl.

Leroy Eckert wrote:

Don: The opening is about 61/4x61/4 plus the angle is there which gives a little
more area. The LCD's have a clear well defined picture that is easy to see. When
I was having trouble with my old TV set/rear monitor I looked at several
different options. One, buy a prefabricated product, plug it in and go. Two, buy
the components and fabricate myself and have what I wanted. In either case I had
to modify the dash panel. The price was about the same. The parts I used are as
follows:

New technology Owls eye camera from http://www.owlseyecamera.com. A bit expensive but
outstanding quality.

Two 3.5 high resolution LCD from http://www.lcdshow.com.

One CC-45 sealed side camera from Steven Birtles http://www.capeinnovation.com I
already purchased all components before Steven began to inventory video parts.

Various connectors and adapters from Radio Shack. BNC, S-video, DVD power
adapters etc.

No matter what you ultimately decide to use, be certain that parts selected
operate in a voltage range or you will need a constant 12v power pack. In my
case, the old system was attached to a power pack, 13.5v in measured 11.9v out.
I hooked the cameras and LCD's to the constant voltage side and all is well. You
will also note that the LCD's I used can be inlaid in the panel because the
electronics are seperated and can be mounted on the back of the panel.
I hope to get lucky and mount the Tire monitor below the LCD's giving a nice
clean custom installation.

I now have an extra Owls eye camera that can be used inside on a system. Check
out that little camera, about as big as my thumb. I have not been able to drive
at night with the set up but have turned it on and the view is good.

If you want I send you the wiring diagram for what I did. It turned out to be a
pretty fun project.

Leroy Eckert
1990WB-40 "Smoke N Mirrors"
Niceville, FL

----- Original Message -----
From: dspithaler@...
To: WanderlodgeForum@yahoogroups.com
Sent: Tuesday, May 15, 2007 7:40 AM
Subject: Re: [WanderlodgeForum] Side Camera

Leroy How big is that panel that your cameras are in. I didn't know you
could put two in that space. You might have more room that mine. Is the
small screen easy to watch? What kind of camera did you get. The install looks
good Thanks
Don
89 SP 36'
Butler, PA

I works very well. I did the right side only as I can see the left side ok.
I did not fool with the turn signal application because I want to see the
right hand dead spot constantly. A couple of weeks ago I installed a new rear
view camera, and two 3.5 high resoultion LCD screens, and fabricated a panel
for the dash. I used the existing on off switch from my old camera and removed
the old contrast brightess potentiometer.
I posted pictures in my 1990 upgrades photo section on the forum. I hope I
have them squared away. The first time I sent them sideways.

Leroy Eckert
1990 WB-40 "Smoke N Mirrors"
Niceville, FL

************************************** See what's free at http://www.aol.com.

[Non-text portions of this message have been removed]

[Non-text portions of this message have been removed]






---------------------------------
Building a website is a piece of cake.
Yahoo! Small Business gives you all the tools to get online.

[Non-text portions of this message have been removed]