Shop air compressor wont put out more than 110 PSI

[Curt Sprenger]

Pete,
I agree with Ernie, please stay with us. Did you tell the new owner about SWBB?

Curt Sprenger
1987 PT38 8V92 "MacAttack Racing"

Anaheim Hills, CA

On Mon, Sep 21, 2009 at 6:25 PM, Pete Masterson <"aeonix1@mac.com"> wrote:

 

Ernie,

Thanks... I'll stay on for awhile ... I suppose my info will get stale at some point since I won't have the continuing experience.

Just got a call from the buyer ... about 2 hours out at a rest stop. He's having a ball with the bus -- even after experiencing some stop-and-go traffic at the fringes of the Bay Area... 

(He needed to know how the door unlocked! ... I'd locked him in when I bid him farewell ... and he'd already forgotten where the lock switches were ... )

Pete Masterson

'95 Blue Bird Wanderlodge WBDA 42 (SOLD)

El Sobrante CA

"aeonix1@mac.com"

On Sep 21, 2009, at 5:04 PM, Ernie Ekberg wrote:

Pete, I see in your sig line you sold your coach. Please stay with us even though you are coachless. Ernie- Twin Peaks, Ca Ernie Ekberg 83PT40 Wanderlodge Weatherford, Tx  817-475-3991 http://autos.groups.yahoo.com/group/erni...gandrepair --- On Mon, 9/21/09, Pete Masterson <"aeonix1@mac.com"> wrote: From: Pete Masterson <"aeonix1@mac.com"> Subject: Re: [WanderlodgeForum] Shop air compressor wont put out more than 110 PSI To: "WanderlodgeForum@yahoogroups.com" Date: Monday, September 21, 2009, 6:23 PM I started out with a cheap compressor much like the one you describe -- it was able to get to 120 psi -- but after a few weeks it failed -- since I bought it at Costco, they took it back with a full credit as defective (under the 1 year warranty). I then bought a 150 psi (max) Rigid-brand "contractors, 4.5 gal, twin stack" compressor from Home Depot. It has proved to be much more reliable. The compressor (may have) two pressure dials and a pressure regulator control knob. This allows you to set the maximum output pressure (to the hose) If the regulator is dialed back a little bit, it may not let the compressor reach maximum pressure. The size/type of output hose should not affect the maximum pressure -- but a smaller hose will reduce the throughput (volume) of air. So filling will take longer and some air-operated tools may not get adequate volume of air at a given pressure. I use a 50'  3/8" hose. It does just fine for my bus tires and the few air operated tools I have, including a 1/2" impact wrench. (I bought one that's more efficient (and expensive) in its required air volume through the tool.) I have one of those vinyl coiled hoses, it's 1/4" -- I've only used it with my auto tires that only need 32 psi. When filling the bus tires, it's usually best to let the compressor cycle on to achieve the maximum pressure. Admittedly, the 150 psi rated compressor I use has a little more oomph and has less trouble getting to 120 psi -- but air delivery (volume) is slower at the higher pressure, so it can take several minutes to get the last few pounds of pressure into the tires.  Some compressors (check the manual) have a maximum cycle time limit (say, 25%) if so, be careful to stop and let the compressor rest from time to time so you don't overheat it. Pete Masterson '95 Blue Bird Wanderlodge WBDA 42 (SOLD!) El Sobrante CA aeonix1@mac. com On Sep 21, 2009, at 1:52 PM, wl89spman wrote: My Porter Cable 135PSI 3HP/4GAL wont put out more than 110psi with 50'rubber hose or 30' coiled yellow vinal(I think). It has always been this way since new. No leaks or problems...My new Michlens need 120 psi so now I have to do something. What psi compressor does everybody use?  Is there a compressor expert here? Does the length and composition of the hose matter? If so what length and material hose do I need for my 135 psi compressor?The output gauge on the compressor reads 130psi but wont pump up tires past 110psi...  Ant help would be appreciated. Ed Gardels 89SP Arlington TxÂÂ