Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Gauge lights will not come on
11-09-2009, 11:26
Post: #6
Gauge lights will not come on
bad ground if they both went off at the same time
Stephen
97BMC37

--- In WanderlodgeForum@yahoogroups.com, nelson slinkman wrote:
>
> Â
> Thanks for all the help. I will check tomorrow on the inverter. I did make
sure both rheostats were all the way clockwise. I will look for the inverters
tomorrow. I did find one wire loose wire. It was a black shielded cable hanging
near the rheostats but did not see any place where it would of attached to. I
think the other end goes somewhere towards the front of the bus. I will have to
take the front off tomorrow and try to find it. It's strange that both the dash
& gauge lights went off at the same time.
> Thanks for the help.
> I will let you know what I find tomorrow.
> Nelson SLinkman
>
>
> --- On Mon, 11/9/09, gregory O wrote:
>
>
> From: gregory O
> Subject: [WanderlodgeForum] Re: Gauge lights will not come on
> To: WanderlodgeForum@yahoogroups.com
> Date: Monday, November 9, 2009, 9:28 AM
>
>
> Â
>
>
>
> Wanderlodge put in a large inverter in my 94pt in the genset rad bay. on the
forward wall, left . they look like a brick, white color
>
> I found one died and I used the other one to run all the lights. the rheostats
control the 12 v into the brick inverters
>
> test that the rheostat control has 12V to the input and then test that it is a
voltage sliding scale on the output as wou rotatte the knob. then I would test
that the voltage output is getting to the inverter then test the ac output of
the inverter.
>
> I tested my el light by lighting them up with ac electric from a pepboys
inverter.
>
> Greg
> 94ptca
>
> --- In WanderlodgeForum@ yahoogroups. com, "cape0001" wrote:
> >
> > DO NOT attach 12 volt dc directly to the dash
> > the dash runs on weird cycle high voltage ac. The dc is inverted to this
> > by 4 inverters under the dash
> > check the grounds on the system then the rheostat controlling the dash
> > check for 12 volt dc going into the inverters (Small Blue Cubes marked high
voltage)
> >
> >
> > --- In WanderlodgeForum@ yahoogroups. com, "Fred Hulse" wrote:
> > >
> > > Nelson
> > > First thought is the dash dimmer switch was turned down.
> > >
> > > Fred & Jeanne Hulse
> > > Morristown Arizona
> > > 1997 Wanderlodge WLWB41
> > >
> >
>
Quote this message in a reply
Post Reply 


Messages In This Thread
Gauge lights will not come on - nelsons - 11-08-2009, 10:01
Gauge lights will not come on - Fred Hulse - 11-08-2009, 11:42
Gauge lights will not come on - cape0001 - 11-08-2009, 12:36
Gauge lights will not come on - gregory O - 11-09-2009, 02:28
Gauge lights will not come on - nelson slinkman - 11-09-2009, 11:25
Gauge lights will not come on - cape0001 - 11-09-2009 11:26
Gauge lights will not come on - nelson slinkman - 11-09-2009, 11:31
Gauge lights will not come on - GARY MINKER - 11-15-2009, 02:54



User(s) browsing this thread: 1 Guest(s)