Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Aux Batt solenoid on PT
05-27-2007, 14:21
Post: #24
Aux Batt solenoid on PT
Scott,

A bad battery could cause the 12.4 reading. Remove the battery, take it
to an auto parts store, have them load test it. Could be a bad cell in
the battery. I've experience battereis with a bad cell start engines,
and then just die on the spot.

What are the "modes" on your multimeter that you are using?

We are here to help. Just keep the communication coming.

Curt Sprenger
1987 PT38 8V92 "MacAttack Racing"
Anaheim Hills, Calif.



Scott Forman wrote:

> the gen batt read 12.1 before I started it, 12.4 after it was
> running. I know that by the book 12.1v is a half-dead battery, but
> it cranks awfully strong to be half dead. And the 12.4 isn't as high
> as it should be, but since it is higher there is obviously some
> charge getting to it...ideas?
>
> Another note...my multimeter has two "modes" that I don't really
> understand. When I turn the dial to one setting, it read 12.4 with
> generator running, on the other setting it read 26.5. Any idea what
> this other mode is showing me?
>
> Much confusions over here
>
> Scott
>
> --- In WanderlodgeForum@yahoogroups.com
> , Curt Sprenger
> wrote:
> >
> > Battery with no charge to it for about 20 minutes, approx 12.6
> volts is
> > good. Battery receiving a charge, 13.4+ volts...unless you have the
> > smart chargers that are in the sleep mode.
> >
> > Curt Sprenger
> > 1987 PT38 8V92 "MacAttack Racing"
> > Anaheim Hills, Calif.
> >
> >
> >
> > Scott Forman wrote:
> >
> > > And what voltage should it show when charging?
> > >
> > > --- In WanderlodgeForum@yahoogroups.com
>
> > > , "pattypape"
>
> > > wrote:
> > > >
> > > >
> > > >
> > > > TO be assured that the gen battery is charging under all
> > > conditions,
> > > > check with the shore power, then generator running , then the
> > > engine
> > > > alternator running and charging.
> > > >
> > > > Bill 88 FC Michigan
> > > >
> > > > --- In WanderlodgeForum@yahoogroups.com
>
> > > , "Scott Forman"
> <sforman@>
> > > > wrote:
> > > > >
> > > > > Isn't it all one circuit?
> > > > >
> > > > >
> > > > >
> > > > > --- In WanderlodgeForum@yahoogroups.com
>
> > > , Curt Sprenger
> > > > > wrote:
> > > > > >
> > > > > > Agree. Good.
> > > > > >
> > > > > > Do the same test using shore power.
> > > > > >
> > > > > > Curt Sprenger
> > > > > > 1987 PT38 8V92 "MacAttack Racing"
> > > > > > Anaheim Hills, Calif.
> > > > > >
> > > > > >
> > > > > >
> > > > > > Scott Forman wrote:
> > > > > >
> > > > > > > OK, the voltage went up with the gen running. So I guess
> the
> > > > > circuit
> > > > > > > works.
> > > > > > >
> > > > > > > Scott
> > > > > > >
> > > > > > > --- In WanderlodgeForum@yahoogroups.com
>
> > >
> > > > > > > , Curt Sprenger
> > > > > > > wrote:
> > > > > > > >
> > > > > > > > Scott,
> > > > > > > > Have you used your multimeter and checked the voltage at
> > > the
> > > > > gen.
> > > > > > > > battery? First before you start the gen. Than again
> after
> > > the
> > > > > gen.
> > > > > > > is
> > > > > > > > running. The increase in voltage when the gen. is
> running
> > > > tells
> > > > > > > you
> > > > > > > > that the charge circuit is working. No change in
> voltage, or
> > > > > > > lower,
> > > > > > > > you know the charge is not working.
> > > > > > > >
> > > > > > > > Curt Sprenger
> > > > > > > > 1987 PT38 8V92 "MacAttack Racing"
> > > > > > > > Anaheim Hills, Calif.
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > > > Scott Forman wrote:
> > > > > > > >
> > > > > > > > > Hmmm..."what is your problem"...there's a wide ranging
> > > > > > > question....
> > > > > > > > >
> > > > > > > > > Really I don't have a problem right now. I am just
> trying
> > > > to
> > > > > learn
> > > > > > > > > my new coach. I knew my old FC inside and out, and
> that
> > > > gave
> > > > > me
> > > > > > > some
> > > > > > > > > confidence that if I ever had a problem on the road,
> > > maybe
> > > > I
> > > > > could
> > > > > > > > > diagnose it & fix it. I want to feel that way about my
> > > PT,
> > > > > too. I
> > > > > > > > > also want to make sure that the charging circuit is
> > > > charging
> > > > > the
> > > > > > > > > generator battery as it is supposed to.
> > > > > > > > >
> > > > > > > > > Scott
> > > > > > > > >
> > > > > > > > > --- In WanderlodgeForum@yahoogroups.com
>
> > >
> > > > > > >
> > > > > > > > > ,
> > > > > > wrote:
> > > > > > > > > >
> > > > > > > > > > Scott,
> > > > > > > > > > May I be so bold as to ask what is your problem?
> > > > > > > > > > Howard Truitt
> > > > > > > > > > Camilla, Ga.
> > > > > > > > > > 86 PT40
> > > > > > > > > >
> > > > > > > > > > >
> > > > > > > > > > > From: "Scott Forman" <sforman@>
> > > > > > > > > > > Date: 2007/05/26 Sat PM 08:17:02 EDT
> > > > > > > > > > > To: WanderlodgeForum@yahoogroups.com
>
> > >
> > > > > > >
> > > > > > > > >
> > > > > > > > > > > Subject: [WanderlodgeForum] Re: Aux Batt solenoid
> on
> > > PT
> > > > > > > > > > >
> > > > > > > > > > > OK...a little help...
> > > > > > > > > > >
> > > > > > > > > > > There are solenoids all over the place. There's
> one
> > > on
> > > > the
> > > > > > > front
> > > > > > > > > > > wall of the batter charger compartment. There are
> two
> > > > > others
> > > > > > > on
> > > > > > > > > the
> > > > > > > > > > > metal panel that folds down to give access to the
> > > > charger
> > > > > > > > > > > compartment. And there are three of them behind
> the
> > > > step
> > > > > well,
> > > > > > > > > > > although it looks like two of them are for the
> > > leveling
> > > > > pump.
> > > > > > > > > None
> > > > > > > > > > > of these make the audible "click" when I hit the
> Aux
> > > > Batt
> > > > > > > > > switch.
> > > > > > > > > > >
> > > > > > > > > > > The drawings in my Blue Box aren't as
> comprehensive
> > > as
> > > > > they
> > > > > > > were
> > > > > > > > > in
> > > > > > > > > > > my FC, so I am having trouble figuring all this
> out.
> > > > > > > > > > >
> > > > > > > > > > > Help!
> > > > > > > > > > >
> > > > > > > > > > > Scott Forman
> > > > > > > > > > > 86 PT38
> > > > > > > > > > >
> > > > > > > > > > > --- In WanderlodgeForum@yahoogroups.com
>
> > >
> > > > > > >
> > > > > > > > > ,
> > > > > > wrote:
> > > > > > > > > > > >
> > > > > > > > > > > > Scott,
> > > > > > > > > > > > On my 86 PT40 mine is in the compartment with
> the
> > > > > chargers.
> > > > > > > But
> > > > > > > > > > > knowing BB and your coach being a 38 footer it
> may be
> > > > > > > different.
> > > > > > > > > > > > Howard Truitt
> > > > > > > > > > > > Camilla, Ga.
> > > > > > > > > > > > 86 PT40
> > > > > > > > > > > > >
> > > > > > > > > > > > > From: "Scott Forman" <sforman@>
> > > > > > > > > > > > > Date: 2007/05/26 Sat PM 02:53:55 EDT
> > > > > > > > > > > > > To: WanderlodgeForum@yahoogroups.com
>
> > >
> > > > > > >
> > > > > > > > >
> > > > > > > > > > > > > Subject: [WanderlodgeForum] Aux Batt solenoid
> on
> > > PT
> > > > > > > > > > > > >
> > > > > > > > > > > > > Where is the auxillary battery solenoid on a
> PT?
> > > > > > > > > > > > >
> > > > > > > > > > > > > Scott Forman
> > > > > > > > > > > > > 86 PT38
> > > > > > > > > > > > >
> > > > > > > > > > > > >
> > > > > > > > > > > > >
> > > > > > > > > > > >
> > > > > > > > > > >
> > > > > > > > > > >
> > > > > > > > > > >
> > > > > > > > > > >
> > > > > > > > > >
> > > > > > > > >
> > > > > > > > >
> > > > > > > >
> > > > > > >
> > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> > >
> >
>
>
Quote this message in a reply
Post Reply 


Messages In This Thread
Aux Batt solenoid on PT - Scott Forman - 05-26-2007, 06:53
Aux Batt solenoid on PT - truitt44@...> - 05-26-2007, 07:48
Aux Batt solenoid on PT - Scott Forman - 05-26-2007, 11:49
Aux Batt solenoid on PT - Curt Sprenger - 05-26-2007, 11:59
Aux Batt solenoid on PT - Scott Forman - 05-26-2007, 12:17
Aux Batt solenoid on PT - Ralph L. Fullenwider - 05-26-2007, 12:35
Aux Batt solenoid on PT - Scott Forman - 05-26-2007, 13:07
Aux Batt solenoid on PT - thomas_sorrentino - 05-26-2007, 15:01
Aux Batt solenoid on PT - Curt Sprenger - 05-26-2007, 18:03
Aux Batt solenoid on PT - truitt44@...> - 05-27-2007, 01:50
Aux Batt solenoid on PT - Scott Forman - 05-27-2007, 02:02
Aux Batt solenoid on PT - truitt44@...> - 05-27-2007, 02:20
Aux Batt solenoid on PT - Curt Sprenger - 05-27-2007, 02:32
Aux Batt solenoid on PT - Scott Forman - 05-27-2007, 10:38
Aux Batt solenoid on PT - Curt Sprenger - 05-27-2007, 10:56
Aux Batt solenoid on PT - Scott Forman - 05-27-2007, 11:05
Aux Batt solenoid on PT - pattypape - 05-27-2007, 11:11
Aux Batt solenoid on PT - Scott Forman - 05-27-2007, 11:24
Aux Batt solenoid on PT - Curt Sprenger - 05-27-2007, 11:28
Aux Batt solenoid on PT - Curt Sprenger - 05-27-2007, 11:29
Aux Batt solenoid on PT - Curt Sprenger - 05-27-2007, 11:33
Aux Batt solenoid on PT - Tom Warner - 05-27-2007, 12:07
Aux Batt solenoid on PT - Scott Forman - 05-27-2007, 12:59
Aux Batt solenoid on PT - Curt Sprenger - 05-27-2007 14:21
Aux Batt solenoid on PT - Scott Forman - 05-27-2007, 14:35
Aux Batt solenoid on PT - Curt Sprenger - 05-27-2007, 14:37
Aux Batt solenoid on PT - Curt Sprenger - 05-27-2007, 14:38
Aux Batt solenoid on PT - Scott Forman - 05-27-2007, 14:42
Aux Batt solenoid on PT - Tom Warner - 05-27-2007, 14:57
Aux Batt solenoid on PT - Curt Sprenger - 05-27-2007, 15:11
Aux Batt solenoid on PT - erniecarpet@... - 05-27-2007, 22:50
Aux Batt solenoid on PT - Pete Masterson - 05-28-2007, 01:05
Aux Batt solenoid on PT - Pete Masterson - 05-28-2007, 01:12
Aux Batt solenoid on PT - Stephen Birtles - 05-28-2007, 02:24
Aux Batt solenoid on PT - Rob Robinson - 05-28-2007, 02:41
Aux Batt solenoid on PT - marvinskaggs@...> - 05-28-2007, 06:09
Aux Batt solenoid on PT - Scott Forman - 05-28-2007, 07:04
Aux Batt solenoid on PT - Travis Martin - 05-28-2007, 07:30



User(s) browsing this thread: