Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Yanmar oil pressure sender
05-07-2008, 13:38
Post: #1
Yanmar oil pressure sender
Does anyone have a NAPA (or otherwise) part number or cross reference
for the Yanmar generator oil pressure sending unit? My oil pressure
sender appears to be shot. Gauge runs all the way to the right
(highest possible pressure reading and then some) when operating.

Also, should the gauge go back to 0 when the sending unit is
disconnected? It doesn't. It does drop to between 60 and 90psi when I
press the "stop" button to warm up the glow plugs, but goes right back
to the top as soon as I hit "start". In fact, disconnecting the
sending unit doesn't seem to have any effect whatsoever on the gauge.

Just in case I replace the sending unit and that doesn't solve it, any
other ideas would be appreciated.

Thank you!

-Ryan
'86 PT-40 8V92
Quote this message in a reply
05-07-2008, 19:27
Post: #2
Yanmar oil pressure sender
Go to ww2.tflx.com for a gauge test guide. It probably also shows a sending unit for that gauge.

Leroy Eckert
1990 WB-40 Smoke N Mirrors
Dahlonega, GA
Royale Conversion

Ryan Wright wrote:
Does anyone have a NAPA (or otherwise) part number or cross reference
for the Yanmar generator oil pressure sending unit? My oil pressure
sender appears to be shot. Gauge runs all the way to the right
(highest possible pressure reading and then some) when operating.

Also, should the gauge go back to 0 when
the sending unit is
disconnected? It doesn't. It does drop to between 60 and 90psi when I
press the "stop" button to warm up the glow plugs, but goes right back
to the top as soon as I hit "start". In fact, disconnecting the
sending unit doesn't seem to have any effect whatsoever on the gauge.

Just in case I replace the sending unit and that doesn't solve it, any
other ideas would be appreciated.

Thank you!

-Ryan
'86 PT-40 8V92




Be a better friend, newshound, and know-it-all with Yahoo! Mobile. [url=http://us.rd.yahoo.com/evt=51733/*http://mobile.yahoo.com/;_ylt=Ahu06i62sR...o8Wcj9tAcJ ] Try it now.[/url]
Quote this message in a reply
05-07-2008, 20:18
Post: #3
Yanmar oil pressure sender
One other thing. I compiled a cross reference for Teleflex gauges a while back. It is in the files. I do not remember if it has the pn for the sender. It's worth a look.

Leroy Eckert
1990 WB-40 Smoke N Mirrors
Dahlonega, GA
Royale Conversion

Ryan Wright wrote:
Does anyone have a NAPA (or otherwise) part number or cross reference
for the Yanmar generator oil pressure sending unit? My oil pressure
sender appears to be shot. Gauge runs all the way to the right
(highest possible pressure reading and then
some) when operating.

Also, should the gauge go back to 0 when the sending unit is
disconnected? It doesn't. It does drop to between 60 and 90psi when I
press the "stop" button to warm up the glow plugs, but goes right back
to the top as soon as I hit "start". In fact, disconnecting the
sending unit doesn't seem to have any effect whatsoever on the gauge.

Just in case I replace the sending unit and that doesn't solve it, any
other ideas would be appreciated.

Thank you!

-Ryan
'86 PT-40 8V92




Be a better friend, newshound, and know-it-all with Yahoo! Mobile. [url=http://us.rd.yahoo.com/evt=51733/*http://mobile.yahoo.com/;_ylt=Ahu06i62sR...o8Wcj9tAcJ ] Try it now.[/url]
Quote this message in a reply
05-08-2008, 00:50
Post: #4
Yanmar oil pressure sender
Ryan,

The sending unit of the vintage Yanmar genset probably follows an SAE
standard. Leroy's suggestion of the Teleflex site ww2.tflx.com was a good
one. The sending unit is a variable resistive device with a linear output
between approximately 240 and 33 ohms. With 0 lbs, the resistance should be
around 240 ohms. You can check this with an ohmmeter (providing you
disconnect the sending unit output wire) and reference to the body of the
sending unit and/or engine ground if it has single wire output, if there are
two output wires, you want to put the meter across both terminals. If the
sending unit ever saw 100 lbs, the resistance should lower close to 33 ohms,
half of that pressure (50 lbs) should produce a resistance close to 100
ohms.

If you want to check the gauge, you could disconnect the wire from the
sender on the gauge 'S' terminal, insert a temporary wire from the now
disconnected sending unit to the gauge, turn the ignition key on and ground
the sending unit. The gauge should read close to "0".

IF you purchased the small ¼ watt resistor pack from Radio Shack for close
to $6 or $7 dollars you could check the gauge by placing a resistor from the
'S' terminal of the gauge to ground.

Full Scale Reading = 240 ohms (two 470 ohm resistors twisted in parallel
will give you 235 ohms

Medium Scale = approximately 100 ohms

0 reading = 33 ohms (a 47 ohm resistor is close, the gauge should almost
read '0'Wink

If there is a question about wiring, you can leave the sending unit in
place, remove the sending unit wire from the 'S' terminal on the oil
pressure gauge and read the resistance to ground with an ohm meter. You
should see something close to 240 ohms with the generator turned off.

Theoretically, you should be able to short the gauge output 'S' terminal and
see the gauge peg. WARNING! I did this recently, shorting the water temp
sending unit wire temporarily to make sure I was hooking up the correct
wire. The gauge pegged and stayed pegged. I've never had that happen. I
didn't realize that would be hazardous to the meter movement. There's
always something to learn.

Donn
76 FC33
South Kingstown, RI


From: WanderlodgeForum@yahoogroups.com
[mailto:WanderlodgeForum@yahoogroups.com] On Behalf Of Ryan Wright
Sent: Wednesday, May 07, 2008 9:39 PM
To: wanderlodgeforum
Subject: [WanderlodgeForum] Yanmar oil pressure sender

Does anyone have a NAPA (or otherwise) part number or cross reference
for the Yanmar generator oil pressure sending unit? My oil pressure
sender appears to be shot. Gauge runs all the way to the right
(highest possible pressure reading and then some) when operating.

Also, should the gauge go back to 0 when the sending unit is
disconnected? It doesn't. It does drop to between 60 and 90psi when I
press the "stop" button to warm up the glow plugs, but goes right back
to the top as soon as I hit "start". In fact, disconnecting the
sending unit doesn't seem to have any effect whatsoever on the gauge.

Just in case I replace the sending unit and that doesn't solve it, any
other ideas would be appreciated.

Thank you!

-Ryan

Quote this message in a reply
05-08-2008, 02:06
Post: #5
Yanmar oil pressure sender
Ryan,

From my Kohler parts catalog part number 258693 for the oil pressure
sending unit. I've been able to call Kohler gen. parts places, give
them the model, serial# and spec # of the generator and get parts.
(Just ordered new slip rings and trying to work up the nerve to try
to replace them myself).
As far as the gauge not going back to zero. I don't think mine does
either. It stays at where it was when I shut it down, until I start
it again.

Tom Sorrentino
1987 PT38
Bedford Hills, NY
12.5 KW yanmar/kohler



--- In WanderlodgeForum@yahoogroups.com, "Ryan Wright"
wrote:
>
> Does anyone have a NAPA (or otherwise) part number or cross
reference
> for the Yanmar generator oil pressure sending unit? My oil pressure
> sender appears to be shot. Gauge runs all the way to the right
> (highest possible pressure reading and then some) when operating.
>
> Also, should the gauge go back to 0 when the sending unit is
> disconnected? It doesn't. It does drop to between 60 and 90psi
when I
> press the "stop" button to warm up the glow plugs, but goes right
back
> to the top as soon as I hit "start". In fact, disconnecting the
> sending unit doesn't seem to have any effect whatsoever on the
gauge.
>
> Just in case I replace the sending unit and that doesn't solve it,
any
> other ideas would be appreciated.
>
> Thank you!
>
> -Ryan
> '86 PT-40 8V92
>
Quote this message in a reply
05-08-2008, 06:27
Post: #6
Yanmar oil pressure sender
Thank you for the responses. I found the cross reference file Leroy
was talking about, and Donald, I really appreciate the testing
instructions. Those will be a huge help. Thanks, Tom, for the part
number and info on your gauge also staying where it was.

-Ryan
'86 PT-40 8V92
Quote this message in a reply
Post Reply 




User(s) browsing this thread: 2 Guest(s)