+- Wanderlodge Gurus - The Member Funded Wanderlodge Forum (http://www.wanderlodgegurus.com)
+-- Forum: Discussions (/forumdisplay.php?fid=21)
+--- Forum: Chassis (/forumdisplay.php?fid=23)
+--- Thread: Air Governor (/showthread.php?tid=9961)
Air Governor - cmillsap - 08-21-2013 22:21
I know I have an air governor on my bus but I have never physically seen it and I am not familiar with how it works.
How wide should the on/off range be on the engine air compressor governor? What are the proper settings? I have noticed that my air governor allows a wider range than I am comfortable with. The air compressor builds to 130psi and remains dormant until the system pressure is reduced to near 80 psi. As the air pressure decreases so does the braking power. It would seem to me that a closer air system pressure range(i'e' 110 to 130) is required to keep the brakes working at their best level to stop the bus.
Chuck
RE: Air Governor - DOSZORROS - 08-22-2013 00:07
Chuck:
Most systems I am familiar with operate between about 90 lbs. and 115 lbs. The air governor controls this. On my 96 bird, I had to replace the air governor and it was mounted inside the frame rail over the drive axle. It took a young man with 5 ft. arms and three elbows to get to it.
On my 2003 LXI, it is right near the air compressor and easy to get to. It normally has a 1/4 inch tube line from the governor to the air compressor. They cost about $20 from any auto parts that caters to the trucking industry. They do go bad and replacement usually solves the problem.
The valves on the air compressor can also get sticky and effect start and stop pressures. You can remove the cover and clean the valves without tearing the air compressor down. It is a fairly simple procedure.
RE: Air Governor - cmillsap - 08-22-2013 00:37
(08-22-2013 00:07)DOSZORROS Wrote: Chuck:
Most systems I am familiar with operate between about 90 lbs. and 115 lbs. The air governor controls this. On my 96 bird, I had to replace the air governor and it was mounted inside the frame rail over the drive axle. It took a young man with 5 ft. arms and three elbows to get to it.
On my 2003 LXI, it is right near the air compressor and easy to get to. It normally has a 1/4 inch tube line from the governor to the air compressor. They cost about $20 from any auto parts that caters to the trucking industry. They do go bad and replacement usually solves the problem.
The valves on the air compressor can also get sticky and effect start and stop pressures. You can remove the cover and clean the valves without tearing the air compressor down. It is a fairly simple procedure.
Thanks, George.... I appreciate the info...I'm gonna have mine serviced..
Chuck
RE: Air Governor - davidbrady - 08-22-2013 10:06
The cut-in pressure sounds a little low to me Chuck. I'll check mine when I get to the bus on Friday but I recollect that the cut-in is around 100 to 105 psi and the cut-out is around 125 to 130 psi.
RE: Air Governor - Endless Summer - 08-22-2013 12:29
Chuck: do you have an air controlled cruise control system? If so do you notice some surging as the bus air pressure drops below 90 lbs?
RE: Air Governor - cmillsap - 08-22-2013 14:01
(08-22-2013 12:29)Endless Summer Wrote: Chuck: do you have an air controlled cruise control system? If so do you notice some surging as the bus air pressure drops below 90 lbs?
Steve, I assumed (maybe erroneously) that the cruise control was electronically controlled but I realy haven't looked at it that closely. I can monitor the setting on the Silverleaf. I haven't noticed any surging as the air pressure drops.
Chuck
RE: Air Governor - davidbrady - 08-23-2013 17:26
Hi Chuck,
I checked my governor at my bus today. It cycles between 100 and 125 psi.