gauge readings 88 FC
|
01-19-2007, 01:54
Post: #5
|
|||
|
|||
gauge readings 88 FC
Bruce,
The 3208 coolant temp. appears to be low, The coolant is really effected by the ambient temp, speed, and hill climbing. It also takes time to get up to a stable operating temp. The thermostat opens at about 185*, Fan kicks on at 195*. These events could be a more accurate indication of temp than the temp gage. So, I would suggest running the 3208 hotter and faster to try to determine if the thermostat is opening properly. oil press. 70 This is good...... Rear axle temp 210 probably not accurate... It could take a full hour of highway driving to reach a stable rear axle running temp. Our 88 rear axle reads about 170* also ambient temp effected ZF temp 195 This is good and rises quickly to the yellow during use. 240/250* Pyro 600 to 650 RPM 2000 (This is good) I have seen 1000* and 13/14 boost. You are correct the gages could be at least 10% off, if they are functioning correctly. My experience with our gages is as follows: The temp gages are really important, the old sensors are not accurate, and the sensors do not always match the gage, I changed both the 3208 oil temp & the rear axle temp gages and matching sensors to get more accurate readings. Sensors need to be matched and purchased thru a Teleflex or Stuart Warner gage distributor. BB is not much help with these old sensors, although BB has a reasonable price on the gages. Volt meters are more accurate, that is why volts are posted to the 10th of a volt, such as 12.7, 13.7 etc. Amp meter accuracy is not criticle, so reading like 25, 50,75 amps is normal. The Onan oil pressure sensor seems to be a higher failure part than the gage. I think this is because of lack of use of the internal diaphram. I replaced the sensor on the Onan to get a more correct reading, 30/60 psi. I have not replaced the Onan temp, gage or sensor, But I know the coolant reads about 20 degrees high. Hope this helps, Bill 88 FC --- In WanderlodgeForum@yahoogroups.com, "birdshill123" > > The following are my readings at a constant 59 mph. flat country. > Water temp. 170 > oil press. 70 > Rear axle temp 210 > ZF temp 195 > Pyro 600 to 650 > RPM 2000 > ambient temp was 55 to 60 > At ambient temp of 75 the water temp climbed to just over 175 > I do not trust any of the gauges. I used my infrared thermometer on > the diff. and it was 160 to 165 depending on where you read. At the > sensor it was 160. I know that my gennie oil prssure is off by 15 lbs. > as I tested it with a non electric hydraulic gauge. I noticed that > when I am in the hills and the turbo kicks in the pyro temps can climb > to over 900. Boost is about 10 to 12. How does all of this look?? > > Bruce 1988 FC35 > " LaReina Gitana" > on the road in Mexico > |
|||
« Next Oldest | Next Newest »
|
Messages In This Thread |
gauge readings 88 FC - birdshill123 - 01-18-2007, 12:33
gauge readings 88 FC - Mike Hohnstein - 01-18-2007, 14:19
gauge readings 88 FC - Tom Warner - 01-18-2007, 15:29
gauge readings 88 FC - one_dusty_hoot - 01-18-2007, 16:43
gauge readings 88 FC - pattypape - 01-19-2007 01:54
gauge readings 88 FC - birdshill123 - 01-19-2007, 02:33
gauge readings 88 FC - Chuck Wheeler - 01-19-2007, 05:28
|
User(s) browsing this thread: 1 Guest(s)