Priming 3208T?
|
09-30-2008, 03:19
Post: #6
|
|||
|
|||
Priming 3208T?
I have always had just as much luck just refilling the racor with
fuel until it is at the top, put the T lid back on and start the engine.......kind of hard to start the engines and ask the wife in "curlers" to tell me when it is "bubbling" out the top. Stop! Good luck. Regards, Hank 90SP36 --- In WanderlodgeForum@yahoogroups.com, "Jeff Miller" wrote: > > If you're only changing the Racor (in '83-up FCS) then change the > filter, leave the T-handle loose on the filter lid, start the > engine, when fuel starts to bubble out around the lid of the Racor > then tighten the T-handle. Self priming. > > And the oil-pressure sender on the oil filter on the '87-up (300hp > ATAAC) 3208 is the one with 2-wires, the single wire ones are for > the gauge and KYSOR system. > > - Jeff > > --- In WanderlodgeForum@yahoogroups.com, "Richard Gideon" > > > > > Alan: You need to place a jumper on the oil pressure switch (near > > oil filters) and then turn on ignition switch...the facet pump > near > > top front of the fuel tank should run and you can check by > listening > > at rear of coach to hear the clicking sound. > > > > If your Facet lift pump is operating you should see positive > pressure > > on the Racor guage by drivers right knee. You will need to open > the > > T-handle on the right front of the injection pump to purge air > from > > the system. > > > > How did you get air into the system...changing Racor? > > > > I'm inside by coach typing this...call Cell 573.465.0527 if I can > > help. > > > > Dick Gideon > > 1989 35FC > > Rolla, MO > > > > > > --- In WanderlodgeForum@yahoogroups.com, "xz3kg7" > > wrote: > > > > > > So, last week I decided to do some "routine" maintenance on my > Bird. > > > Why is it that I always get into something when I do routine > > > maintenance? ![]() > > > > > > How do I prime my 87 3208T? I read some posts about a "prime > pump", > > > but I don't know if mine has one. Below is how I got to this > > problem, > > > if it matters. > > > > > > Thanks, > > > Alan > > > 87FC35 > > > > > > Here's what happened. I took off my doghouse, which included > > > disconnecting the guage on the side of the doghouse for the > Racor. > > > Later on, I decided I needed to turn my Bird around so I would > be in > > > the shade. While I was moving it, it started idling rough. Being > the > > > quick thinker that I am, I remembered the hose that was > connected to > > > the Racor. When I put my finger over the hose, it started running > > > better. I finished turning it around, left it running to go > check on > > > if I had it positioned where I wanted it (now without my finger > on > > the > > > hose). It then started idling rough again and died. > > > > > > I finished my maintenance, reconnected the racor guage and tried > to > > > start it, but it seems to not be getting fuel. I'm pretty sure > it > > had > > > something to do with my disconnecting the guage. > > > > > > |
|||
« Next Oldest | Next Newest »
|
Messages In This Thread |
Priming 3208T? - xz3kg7 - 09-29-2008, 05:43
Priming 3208T? - Kurt Horvath - 09-29-2008, 05:53
Priming 3208T? - bubblerboy64 - 09-29-2008, 06:14
Priming 3208T? - Richard Gideon - 09-29-2008, 06:15
Priming 3208T? - Jeff Miller - 09-29-2008, 13:11
Priming 3208T? - Henry Jay Hannigan - 09-30-2008 03:19
|
User(s) browsing this thread: 1 Guest(s)